Psion Teklogix PrintAbout MP2000 Návod k obsluze Strana 1

Procházejte online nebo si stáhněte Návod k obsluze pro Tisk a skenování Psion Teklogix PrintAbout MP2000. Psion Teklogix PrintAbout MP2000 Operator`s manual Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk

Shrnutí obsahu

Strany 1 - Operator’s Manual

PrintAbout MP2000 Series Operator’s Manual Psion Teklogix Corporation 3000 Kustom Drive Hebron, KY 41048 800-322-3437 www.psionteklo

Strany 2

Getting Started Release LeverBattery Contacts Figure 2 - Battery Installation To charge the battery, connect an optional power supply to the approp

Strany 3

Getting Started Installing Media Each printer comes supplied with a roll of receipt paper. Note: For maximum performance and optimum print qualit

Strany 4

Getting Started Turning the Printer On and Off Refer to Figure 5 and locate the printer’s Power Button. To turn the printer on, simply press and rel

Strany 5 - TABLE OF CONTENTS

Getting Started Removing Printer Output To tear the paper, pull the paper against the tear bar (a sharp edge on the paper door) at a slight angle as s

Strany 6

Getting Started Using The Carrying Strap The printer’s flexible carrying strap with multiple hook-and-loop fasteners is designed to be used in a vari

Strany 7 - Introduction

Daily Operation Introduction For normal daily use, most users will only need to turn the printer on and off, tear off printed output, load paper, an

Strany 8

Daily Operation Symbol Function Status Power Button Used to turn the printer on or off. Paper Feed Button Advances paper a preset distance or to

Strany 9 - Getting Started

Daily Operation Battery Charging The PrintAbout contains battery monitoring and charging circuitry so that the battery may be charged while in the pr

Strany 10

Daily Operation Using the Magnetic Card Reader The optional Magnetic Card Reader (MCR) may be used by some applications to read information from cred

Strany 11 - Installing Media

Printer Configuration Introduction This section describes printer operating features that may be configured to allow PrintAbout series printers to co

Strany 12

FCC Part 15 Class B This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may no

Strany 13 - Host Interface Set Up

Printer Configuration INTERFACE MENU – Bluetooth Selected Modify From Menu Item Values Default Value Control Panel Setup Utility Emulation Printek

Strany 14 - Using The Carrying Strap

Printer Configuration PRINT ALL LOGOS IN MEMORY Modify From Menu Item Values Default Value Control Panel Setup Utility Print All Logos in Memory n

Strany 15 - Daily Operation

Printer Configuration Serial Interface The following Serial Interface Menu features are only available and/or only take affect when the Serial Interfa

Strany 16

Printer Configuration ETX/ACK Handshaking Possible Values: Off*, On This feature enables or disables the ETX/ACK character handshaking method used to

Strany 17 - Battery Charging

Printer Configuration Discoverability Possible Values: Off, On* This feature is used to set whether the printer may be discovered by other Bluetooth

Strany 18 - MCR Indicato

Printer Configuration WLAN Type Possible Values: Infrastructure*, Peer-to-Peer This feature specifies the type of wireless network the printer will b

Strany 19 - Printer Configuration

Printer Configuration WLAN Auth Possible Values: Auto*, Open, Shared This feature specifies the authentication method that will be used when establis

Strany 20

Printer Configuration Format Menu The features contained in the Format Menu affect the location and appearance of the data printed. Note: Factory

Strany 21 - Interface Menu

Printer Configuration Print Contrast Possible Values: -35% … 0* … +35% in increments of 5% The printer automatically adjusts the amount of energy use

Strany 22 - Serial Interface

Printer Configuration Print All Logos In Memory This menu item is only available using Control Panel Setup and is only available if downloaded fonts

Strany 23 - Bluetooth Interface

Read all setup and operating instructions before proceeding with operation. Do not operate in an enclosure unless properly ventilated. Make sure n

Strany 24 - Wi-Fi Interface

Printer Configuration Insert This End First Snap In This End Second Figure 12 - Paper Guides Auto Power Down Possible Values: Off*, 1 Minute Dela

Strany 25

Printer Configuration Hardware Menu Features in the Hardware Menu are used for software development/debugging and/or printer configuration. These fe

Strany 26

Printer Configuration Using Setup After the Setup mode is entered, instructions will be printed indicating that the Power Button may be used as a “Sel

Strany 27 - Format Menu

Interfacing To A Host Computer Every PrintAbout printer is equipped with a Universal Port which contains a Serial Interface. The Serial Interface ma

Strany 28

Interfacing to a Host Computer Figure 14 and Figure 15 show the location of the Universal Port Connector and the connector pin assignments. Caution:

Strany 29 - Options Menu

Interfacing to a Host Computer Operating as a server, other devices such as a PDA or other host computer may initiate the connection to the printer.

Strany 31 - Control Panel Setup

Power Considerations PrintAbout printers are designed to provide superior output using as little power as necessary. This provides the longest possi

Strany 33

Maintenance and Troubleshooting Cleaning In normal environments, the printer should be cleaned after printing a few rolls of paper or if there are vo

Strany 35 - Interface

Maintenance and Troubleshooting Battery Care Charging the Battery The printer’s battery is charged in the printer using an optional power supply. Pow

Strany 36

Maintenance and Troubleshooting Testing the Power Supply and Battery To verify that the printer’s internal battery charger is functioning properly, pe

Strany 37 - Power Considerations

Maintenance and Troubleshooting Troubleshooting When encountering problems, the cause may be the printer or may sometimes be due to other problems wit

Strany 38

Maintenance and Troubleshooting Problem Possible Cause Solution Battery not charging. Faulty power supply or battery. Refer to “Testing the Power Su

Strany 40 - Battery Care

Print & Font Samples Print Samples 39

Strany 41

Print & Font Samples Courier Font With International Extended Character Set Courier Font PC Line Drawing Extended Character Set 40

Strany 42 - Other Problems

Print & Font Samples Sans Serif Font 41

Strany 44

Specifications Printer Specifications Printing Specifications Printing Method: Direct Thermal, Up To 2.8 Inches Per Second Printing Resolution:

Strany 46

Specifications Physical Specifications Size: 6.1 x 5.9 x 2.7 inches, 15.5 x 15.0 x 6.9 cm (LxWxH) Weight: 20 Ounces (.57 kg) with battery Enviro

Strany 47 - Sans Serif Font

Specifications Media Specifications Receipt Paper General Specifications: 0.0022 to 0.0065” (0.056 to 0.089mm) Thick 2.9 to 4.125” (73.66 to 104.78

Strany 48

Specifications Supplies and Accessories Supplies Battery: 7.4V, 2200 mAH Li-Ion Available separately or in 5 or 20 packs. Media: 3.125” and 4.125”

Strany 49 - Specifications

Glossary of Terms 802.11 Wireless networking communication standards created by IEEE. access point An interface between a wireless network and a wir

Strany 50

Glossary IP Internet Protocol. A specification for packets, or datagrams, of data and an addressing method to allow the exchange of data with anothe

Strany 53 - Glossary of Terms

Introduction Thank you for purchasing a Psion Teklogix PrintAbout Series mobile thermal printer. The PrintAbout series offers a variety of configur

Strany 55

Getting Started Printer Features Before preparing your new PrintAbout for use, please refer to Figure 1 and familiarize yourself with the locations

Komentáře k této Příručce

Žádné komentáře