Psion Teklogix PowerScan M8300 Uživatelský manuál Strana 47
- Strana / 220
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
POWERSCAN
®
D8330/M8300
30
Read the BC-80X0 restore default code:
9.
Restore BC-80X0 Default
Ì$+RX0$-qÎ
Go to section 4.8 Interface Selection.
4.5.1 Using Multiple M-Series Readers with Same Cradle
If you want to use several M-Series readers with the same BC-80X0 cradle, you must
first Bind the cradle with one of the readers (see previously described configuration
procedure).
Successive readers
can be associated with the same cradle by following the
configuration procedure substituting the Bind command with Join (step 7).
7.
Join
Ì$+RN1$-NÎ
The green LED on the PowerScan
®
M8300 will blink: the reader is ready to be
positioned onto the cradle. Complete step 8.
END of procedure.
CAUTION
All readers associated with the same cradle must have different
addresses.
YOUR READER IS NOW READY TO READ BAR CODES.
To change the defaults see section 4.10.
- Psion Teklogix 1
- PowerScan 1
- D8330/M8300 1
- COMPLIANCE 7
- LASER SAFETY COMPLIANCE 9
- LED CLASS 10
- IC (INDUSTRY CANADA) 10
- 1999/5/EEC R&TTE 11
- CONTENTS 13
- GENERAL VIEW 16
- Figure C – BC-8000 17
- Figure D – C-8000 17
- 1 INTRODUCTION 18
- 2 INSTALLATION 19
- INSTALLATION 20
- CAUTION 20
- 2.3 RS-232 CONNECTION 22
- 2.4 USB 22
- 2.5 IBM USB POS 23
- 2.6 WEDGE CONNECTION 24
- 2.8 NETWORK CONNECTIONS 25
- 2.8.2 Network Cabling 26
- 2.8.3 Network Termination 27
- 2.9.2 Replacing PowerScan 28
- M8300 Batteries 28
- 2.9 POWERSCAN 28
- M8300 BATTERY MAINTENANCE 28
- 2.9.1 Battery Charging 28
- 2.10.1 Desktop Mounting 30
- Portable Desktop Use 31
- Fixed Desktop Use 31
- 2.10.2 Wall Mounting 33
- Inclined Base Wall-mounting 34
- 3 POWERSCAN 35
- M8300 SYSTEM AND NETWORK 35
- LAYOUTS 35
- 3.1.4 C-BOX Layout 37
- 3.2.1 Host Master Layout 38
- 3.2.2 BC-8060 Master Layout 39
- /*32: FAIL*/ 40
- 4 CONFIGURATION 41
- 4.1.3 Copy Command 42
- 4.2 SETUP PROCEDURES 42
- Ì$+$*oÎ 44
- ÌIB'Î 45
- ÌRA0RFHÎ 46
- Ì$+RN0$-IÎ 46
- Ì$+RX0$-qÎ 47
- Ì$+RN1$-NÎ 47
- 4.5.2 PowerScan 48
- 4.6 POWERSCAN 49
- M8300/STAR-SYSTEM™ SETUP 49
- Ì$+RF4Î 51
- Ì$+RZ2$-ÇÎ 52
- Ì$+RZ1$-~Î 52
- Ì$+CP0$-$Î 53
- Ì$+CM2EC0$->Î 53
- Ì$+CM1$-ÈÎ 53
- Ì$+CM0$-ÃÎ 53
- Ì$+CP6$-BÎ 53
- First Start-Up 56
- CONFIGURATION 58
- RS-232 PARAMETERS 59
- ANDSHAKING 61
- USB PARAMETERS 64
- USB-COM 65
- USB-KBD 67
- EYBOARD 67
- ATIONALITY 67
- WEDGE PARAMETERS 70
- HARACTER 76
- MULATION 76
- PEN EMULATION 77
- PERATING 78
- NETWORK PARAMETERS 82
- ERMINATOR 86
- DATA FORMAT 87
- DJUSTMENT 93
- EPLACEMENT 95
- POWER SAVE 100
- READING PARAMETERS 101
- NTENSITY 104
- DECODING PARAMETERS 107
- CODE SELECTION 110
- Ì#+AUTOWÎ 111
- ADVANCED FORMATTING 128
- ONCATENATION 129
- DVANCED 132
- ORMATTING 132
- RADIO PARAMETERS 147
- ONTROL FOR 150
- DISPLAY PARAMETERS 153
- 5 REFERENCES 157
- 5.1.2 ACK/NACK Protocol 158
- 5.1.3 FIFO 159
- 5.1.4 RX Timeout 160
- 5.2 PEN PARAMETERS 160
- 5.2.1 Minimum Output Pulse 160
- 5.2.3 Overflow 161
- 5.2.5 Inter-Block Delay 162
- 5.3 NETWORK PARAMETERS 162
- 5.4 DATA FORMAT 163
- POWERSCAN® D8330/M8300 167
- (accent) 168
- ÌFQ9C2>Î 170
- 5.4.3 Address Stamping 172
- 5.4.4 Address Delimiter 172
- 5.4.5 Time Stamping Format 173
- 5.5 POWER SAVE 173
- 5.5.1 Sleep State 173
- REFERENCES 174
- 5.6.5 Safety Time 175
- 5.7 DECODING PARAMETERS 175
- 5.7.1 Ink-Spread 175
- 5.7.2 Overflow Control 175
- 5.7.3 Interdigit Control 176
- 5.8 ADVANCED FORMATTING 176
- 5.8.1 Match Conditions 176
- 5.9.2 Radio RX Timeout 177
- 5.9.3 Power-Off Timeout 177
- 5.9.4 Transmission Mode 178
- 5.9.6 Single Store 179
- 5.9.7 Batch Mode 179
- 5.9.8 Find Me (PowerScan 180
- M8300 only) 180
- 5.10.1 Display Mode 181
- Ì$+$0ÂÎ 183
- Ì$+$1$Î 183
- Ì#+CODEÂÎ 183
- Ì$+ZZ0$-*Î 184
- Ì$+ZZ2$-4Î 185
- Ì$+ZZ3$-9Î 186
- Ì$+RN2$-SÎ 188
- 6 MESSAGE FORMATTING 189
- 6.1.1 Cursor Control 190
- 6.1.2 Font Selection 191
- 6.1.3 Clearing Display 191
- 6.1.5 Setting RTC 192
- 7 TECHNICAL FEATURES 194
- 7.2 POWERSCAN 195
- 7.3 BC-80X0 / C-8000 196
- 7.5 STATUS INDICATORS 197
- 7.6 READING DIAGRAMS 200
- POWERSCAN 201
- SERIAL CONFIGURATION STRINGS 202
- (ms) CK00 - CK99 203
- (100 ms) CL00 - CL99 203
- (not for USB-KBD-ALT-MODE) 204
- (IBM AT compatible only) 204
- (100 ms) CK00-CK99 206
- (only for D8330 series) 209
- B CODE IDENTIFIER TABLE 215
- C HEX AND NUMERIC TABLE 218
- HEX / NUMERIC TABLE 219
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.059 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce